Reduce excess chemical overfeed with the Q46S Residual Sulfite monitor

Maintaining a small amount of residual sulfite to control the removal of chlorine before discharge to the environment from clean water and also waste water effluent is common practice in many facilities.

Strongly reducing sulfur compounds such as SO2 gas, sodium sulfite or sodium bisulfite solutions are used to eliminate chlorine residuals that might prove toxic to fish and other wildlife in the receiving streams or rivers.

However, because residual chlorine discharge limits are often very close to zero, water quality monitoring residual values to comply with regulations has become very difficult and controlling residuals at values between zero and 10 or 20 parts-per-billion is often not achievable.

To meet stringent discharge limits, the sulfite or bisulfite used for de-chlorination is added in slight excess, providing a small sulfite residual to ensure complete de-chlorination.

This excess must be carefully controlled and monitored and ATi’s Q46S/66 provides operators with a reliable tool for maintaining a small sulfite residual while reducing excess chemical consumption due to overfeed.

Theory of operation

Because measuring the SO3= ion in solution is relatively difficult, the Q46S/66 Residual Sulfite monitor takes a different approach to the measurement, employing a unique gas-phase method to continuously monitor sulfite without contact between the sensor and the water sample, eliminating the potential for sensor fouling, plus the risk of formation of H2S on the GAC filters is reduced.

Gas phase approach to sulfite measurement

In operation, a small amount of sample is pumped into the system and mixed with acid. In acidic solution, the sulfite ion is converted to sulfur dioxide gas as follows:

SO3= + 2H+ → SO2 + H2O

The mixed sample flows into a special chamber where the sulfur dioxide is stripped from the sample. A gas conditioning module prepares the gas sample for measurement prior to contact with a special SO2 gas sensor designed for the system. Sensor signals are amplified and displayed on a large-format, backlit LCD display in the Q46S Residual Sulfite monitor electronics unit.

Maintenance

Sulfite monitoring systems are extremely easy to operate and maintain, with acid usage of one gallon/4.5 litres every 25 days at standard flow rates. Sample and acid are pumped using long life peristaltic pump tubing that requires replacement approximately every 6 months.

Pump heads are designed for easy tube changes, requiring about 10 minutes to replace both pump tubes. The sulfite sensor requires no maintenance other than an occasional visual inspection to ensure that no deposits have collected due to airborne particulates.

The gas stripping technique for monitoring sulfite in solution provides an extremely sensitive on-line monitor. Measurements down to low parts-per-billion can be done easily, and zero and span stability inherent in the sensor allow for monthly calibration cycles.

Chemical savings

Maintaining a small sulfite residual in dechlorinated water has the benefit of insuring complete de-chlorination. Monitoring the concentration of this residual allows chemical feed control that can result in significant chemical cost savings. The best way to look at potential chemical savings is to calculate the cost of each PPM of residual sulfite in a specific volume of de-chlorinated water.

Features

Sulfite Measurement
Sulfite ion is measured selectively by conversion to sulfur dioxide.

Gas Phase Sensing
Measurement is made without contact between sample and sensor, eliminating the potential for sensor fouling.

Chemistry Module Power Options
Power options include 115 or 230 VAC, 50/60 Hz.

Three Control Relays
Relays are programmable for setpoint, deadband, and time delay.

Sample Line Cleaning
Internal sequencing and relay system for automated sample line cleaning.

Digital Communication
Communication options for Profibus-DP, Modbus-RTU, or Ethernet-IP.

Featured Article

Related content



News icon
News
Delivering smart water solutions across the entire distribut…

Our smart water, source-to-tap solutions encompass flow measurement, water quality monitoring and data analytics…

Read
Editorial icon
Editorial
Reducing water scarcity with smart water solutions

In the UK there is growing concern that we could be heading for a future of increasing water scarcity, as the surge…

Read
News icon
News
See a clearer picture of your network with NephNet

Following extensive research and listening to our customers’ requirements, ATi UK’s Innovation Hub have re-engineered and…

Read


A team of experts, ready to help

A global company with a caring culture. We have a team of experts on hand to help with any product or support query you may have. Contact us and experience ATi’s exemplary customer support.

Get in touch